Hi, I have noticed that the windscreen washers on my F10 LCI are not working particularly well of late. When I pull the stalk, I can hear the motor whirr but no water initially followed by a little water reaching just the very bottom section of the windscreen. I know from previous 5's that I've had that sometimes in cold weather one of the water feed pipe junctions can pop off so I was thinking it might be something similar (even though it is still unseasonably warm at the moment). I popped the bonnet and pulled the stalk but didnt spot anywhere spurting water. My next guess is a connection around the resevoir bottle and pump which I am assuming is still in the drivers side wheel arch? Before I strip that back I thought I'd ask the question here in case there is something else I should be considering? Cheers, ~Shaun.
Have you been using none BMW screenwash? If so the filter to the pump gungs up and will eventually stop water coming through. You could put some Milton in the reservoir. When I had the F11 I got to the tank but it was a pain in the deriere as had to take the front right plastic inner wing off to get to it. Once sorted just use BMW approved screenwash
Ahh ok that's probably it so, I have never used 'official' screenwash on any car I've owned. Looks like I will have to get the wheel arch liner off so to get to the filter for one good cleaning and then start on the 'approved' screenwash? Or does the Milton fix the issue without physically getting to the tank? ~S.
I don’t think it is necessarily using the BMW specific screen wash, although I could be wrong, it is more about sticking to one brand/type. Multiple brands/types when mixed can create a reaction that causes gunking. I had this with an E92, totally blocked nozzles, took the washer bottle out from behind the wheel arch, both filters were blocked. New filters and BMW fluid from then on and all was well. With my two brand new cars (G22 and the current G21) I’ve only used the BMW stuff.
Thanks all, After a little googling I discovered a handy way of unblocking the filters which I just did at lunch time. Essentially disconnect the feed pipe under the bonnet and open the resevoir tank lid, then send some compressed air down the pipe to blow any crud blocking the filter from the other direction. Took 30sec all in to do and now washers are back to their former glory. I did also pop out and get a couple of bottles of Sonax Clear View 1:100 Concentrate to use going forward. According to Mr Internet this may be what the bmw fluid is based on?? (unverified). Anyway lesson learned, everyday is a school day etc.. ~Shaunos.
The black gunge will return soon. I ended up taking the tank off to get rid of it all. Just stick to the same brand of screen wash and you will be ok. BMW make cars not screen wash ???.
I think an important tip is to actually use the washers too, many hardly use them and the fluid get old and turns to jelly blocking the filters in the bottle. As others have said probably worth removing the bottle this once giving it all a really good clean out and then sticking to one brand (I use Prestone without issues) and make sure you cycle through the fluid.
Another classic remedy is to use denture cleaning tablets... crush up a couple and pop them into the tank, flushed down with a cup full of hot water. They dissolve the residue very nicely. Likewise, if you have any cups/mugs full of tea/coffee stains, one tablet per cup, fill with hot water and leave overnight... rinse a couple of times in the morning and it's like a new cup.
I tried the above and all sorts even drain cleaner and extending the pipes to keep it off the paint but tank off was the answer in the end. Anything is worth a try you might be lucky but then again it might work for a short time after disturbing the gunge.
Stay away from cheap screenwash, Sonax is as good as BMW stuff, the BMW stuff I use is winter rated so a bottle lasts from spring to winter, and I'll get through another over winter when I up the concentration. Anything with a silly scent is going to cause issues with crap growing in there, you can drop a Milton tab in every 3 months once you have washed the tank out, all you have done now is blow the crap off the filter, it'll be back on there soon enough.
Thanks again for all the replies, I have noticed the performance start to degrade again, not yet back to where it was but yeah it looks like I'll have to strip the wheel arch liner and clean everything up properly . I have to replace both front wishbones on my wifes car next weekend (weather permitting) so I'll either be in the mood to do it then or fed up with car DIY for one day Anyway I have the can of compressed air in the boot which will keep me good until I get around to cleaning things out properly. ~S.